CA Design > Printed Circuit Board (PCB) Design, Printed Circuit Board (PCB) Layout and Printed Circuit Board (PCB) Training

PRINTED CIRCUIT BOARD DESIGN SERVICE BUREAU

CA DESIGN

Intake Document

Download Adobe Acrobat format

Download Microsoft Word format

This document is intended to be use by the designers at CA Design as a tool to provide the customer with
the highest possible quality in the design and documentation of their PCB.

Please take a minute and fill out as much of the document as is applicable. If a line is not applicable, please write "N/A".

Name Company		Email Phone
Schematic Diagram:
1. Software:

2. Will CA Design input your schematic into OrCAD?				Yes No
If yes: Does CA Design have all data sheets for your parts?				Yes No

3. Do you have a Nets List from your schematic?				Yes No

4. What format is the Nets List in?

Bill Of Materials:
1. Do you have a final Bill Of Materials for your design?				Yes No

2. Are all parts fully defined?				Yes No

3. Do you have data sheets for all parts?				Yes No

Board Outline:
1. Do you have a mechanical drawing of the Board Outline?				Yes No

2. Is the board outline in Electronic Format?				Yes No
If Yes: What type of format? PADS, OrCAD, DXF or Other?	PADS OrCAD DXF Other

3. Are all connector mounting locations defined?				Yes No

4. Are all trace and component keep-out areas defined?				Yes No

5. Are mounting holes connected to ground?				Yes No
Connector mounting holes connected to ground?				Yes No

6. What are the silkcreen marking requirements?

PCB Design Database:
1. Board should be designed in what type of software?

2. Do you require Fabrication and Assembly Drawings?				Yes No

3. Do you have sample drawings of your Fab and Assy?				Yes No

4. Do you have your company formats on DXF or other CAD Database?				Yes No

5. Do you havea preferred set of Fabrication Drawing Notes?				Yes No

6. Do you require re-numbering for Reference Designations?				Yes No
If Yes: Pattern Style (left-right, Top- Bottom): Desired Was-Is format?

Placement:
1. Do you have a pre-placement sketch				Yes No

2. Are there special requirements for placement? Such as height, thermal, spacing, clock length?

3. Are there components on both sides of the board?				Yes No

4. How should the decoupling capacitors be placed?

5. Are there "Extra" caps on the schematic?				Yes No
Can we add or delete surplus decoupling caps?				Yes No

6. Are the "sources and termination's" defined on the schematic for Terminating Resistors?				Yes No

7. What size plots would you like for the Placement Review?

8. Which, if any, components require sockets?

Routing:
1. Do you have a list of your critical nets?				Yes No

2. Describe any special concerns for critical nets.

3. What is your desired Layer Stack-up?			Optimal Optional

4. What is the desired Via size?			hole		pad

5. What are the minimal trace size and spacing?
Net Type:
Size
via to via
via to pad
via to signal
signal to signal
signal to pad
pad to pad
copper pour clearances

6. Are there any special clearance requirements?				Yes No

Panelization and Test
1. Is a Panel Drawing Required?				Yes No

2. Do you require the Gerber data in Panelized format?				Yes No

3. Do you require a test point on every signal?				Yes No

4. What size and spacing is required for the test points?

Deliverables:
1. Please check off the required deliverables:
A. Database on disk:	OrCAD PADS
B. Gerber Data on disk.
C. Drill Data on disk.
D. DXF of Assembly Drawing on Disk
E. DXF of Fabrication Drawing on Disk
F. DXF of Panel Drawing on Disk
G. Was-Is file on disk.
H. Pen plots of:
Artwork
Assembly Drawing
Fabrication Drawing
Panel Drawing
I. Positive Film plots of Artwork - Negative Film plots of Artwork
J. Other:

CA DESIGN Intake Document

CA DESIGN

Intake Document